Address
304 North Cardinal
St. Dorchester Center, MA 02124

Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM

How to take apart a dirt devil vacuum cleaner

Learn how to take apart a Dirt Devil vacuum cleaner in this step-by-step guide. We'll show you how to access and clean or repair the various parts of your vacuum, helping to keep it in good working condition. Plus, we'll provide tips for reassembling your vacuum and getting it working like new again.

Are you trying to clean or repair your Dirt Devil vacuum cleaner but don’t know how to take it apart? Don’t worry, you’re not alone. Many people struggle with disassembling their vacuum cleaners, but it’s actually a simple process once you know what to do.

In this guide, we’ll walk you through the steps for taking apart a Dirt Devil vacuum cleaner. We’ll also provide some tips for keeping your vacuum in good working condition and for making the reassembly process as easy as possible.

Before we get started, there are a few things you’ll need to have on hand:

  • A flat surface to work on
  • A Phillips head screwdriver
  • A small flathead screwdriver
  • A pair of needle-nose pliers
  • A small brush (such as a toothbrush)
  • A can of compressed air
  • A vacuum cleaner belt (if your vacuum needs a new one)

Now, let’s get started!

Step 1: Unplug the vacuum cleaner

Before you do anything else, make sure you unplug the vacuum cleaner from the outlet. This is an important safety precaution that will prevent you from getting shocked or damaging the vacuum.

Step 2: Remove the dustbin

The first step in taking apart a Dirt Devil vacuum cleaner is to remove the dustbin. This is typically located on the top or side of the vacuum, and it’s where all the dirt and debris collect.

To remove the dustbin, first locate the release button or latch. This is usually a small button or lever that you can press or slide to release the dustbin. Once you’ve found the release button, press or slide it and gently pull the dustbin out of the vacuum.

Step 3: Remove the filters

Once you’ve removed the dustbin, the next step is to take out the filters. These are typically located inside the dustbin or behind the dustbin compartment.

To remove the filters, first locate the filter release button or latch. This is usually a small button or lever that you can press or slide to release the filters. Once you’ve found the release button, press or slide it and gently pull the filters out of the vacuum.

If your Dirt Devil vacuum has more than one filter, be sure to remove all of them.

Step 4: Clean the filters

Now that you’ve removed the filters from your Dirt Devil vacuum, it’s time to clean them. This is an important step because dirty or clogged filters can reduce the suction power of your vacuum and can even cause it to overheat.

To clean the filters, first use a small brush (such as a toothbrush) to gently remove any visible dirt or debris. Then, use a can of compressed air to blow out any remaining dirt or dust.

If your filters are very dirty or clogged, you may need to wash them. To do this, follow the instructions in your vacuum’s owner’s manual.

Step 5: Remove the belt

If your Dirt Devil vacuum uses a belt to drive the brush roll, the next step is to remove the belt. This is typically located underneath the vacuum, near the brush roll.

To remove the belt, first locate the belt release button or latch. This is usually a small button or lever that you can press or slide to release the belt. Once you’ve found the release button, press or slide it and gently pull the belt off the brush roll.

If your belt is worn or damaged, now is a good time to replace it with a new one. Simply slide the new belt onto the brush roll and make sure it’s seated properly.

Step 6: Remove the brush roll

The next step in taking apart your Dirt Devil vacuum is to remove the brush roll. This is typically located underneath the vacuum, near the front of the cleaning head.

To remove the brush roll, first locate the brush roll release button or latch. This is usually a small button or lever that you can press or slide to release the brush roll. Once you’ve found the release button, press or slide it and gently pull the brush roll out of the vacuum.

Step 7: Clean the brush roll

Once you’ve removed the brush roll, it’s time to clean it. This is an important step because a dirty or clogged brush roll can reduce the suction power of your vacuum and can even cause it to overheat.

To clean the brush roll, first use a small brush (such as a toothbrush) to gently remove any visible dirt or debris. Then, use a can of compressed air to blow out any remaining dirt or dust.

Step 8: Remove the base plate

The next step in taking apart your Dirt Devil vacuum is to remove the base plate. This is typically located underneath the vacuum, near the back of the cleaning head.

To remove the base plate, first locate the base plate release button or latch. This is usually a small button or lever that you can press or slide to release the base plate. Once you’ve found the release button, press or slide it and gently pull the base plate off the vacuum.

Step 9: Remove the screws

Once you’ve removed the base plate, the next step is to remove the screws that hold the vacuum cleaner together. These are typically located along the edges of the vacuum, and they can be removed using a Phillips head screwdriver.

Remove all of the screws, and keep track of where they came from. This will make it easier to reassemble the vacuum later.

Step 10: Separate the body of the vacuum

Once you’ve removed all of the screws, you should be able to separate the body of the vacuum into two pieces. To do this, simply lift the top half of the vacuum off the bottom half.

Step 11: Clean the inside of the vacuum

Now that you’ve taken apart your Dirt Devil vacuum, it’s time to clean the inside. This is an important step because it will help improve the suction power of your vacuum and will prevent it from overheating.

To clean the inside of the vacuum, first use a small brush (such as a toothbrush) to gently remove any visible dirt or debris. Then, use a can of compressed air to blow out any remaining dirt or dust.

If your vacuum has a motor or other parts that need to be cleaned, refer to your owner’s manual for specific instructions.

Step 12: Reassemble the vacuum

Once you’ve cleaned the inside of your Dirt Devil vacuum, it’s time to reassemble it. To do this, simply follow the steps above in reverse order.

Start by putting the top half of the vacuum back onto the bottom half. Then, replace the screws that you removed earlier, making sure to put them back in the same place.

Next, replace the base plate and the brush roll, making sure they’re seated properly. Then, replace the belt (if necessary) and the filters. Finally, replace the dustbin, making sure it’s securely attached.

Once you’ve completed these steps, your Dirt Devil vacuum should be back together and ready to use.

Youtube Tutorial on disassembling dirt devil vacuum

How do you assemble a dirt Devil upright vacuum?

Once you’ve cleaned or repaired your Dirt Devil vacuum, it’s time to put it back together. This is an important step because a properly assembled vacuum will work more efficiently and will be less likely to break down.

Here are some tips for putting your Dirt Devil vacuum cleaner back together:

  • Start by referring to the owner’s manual: This will provide specific instructions for your make and model of vacuum, and it will help you avoid making mistakes.
  • Follow the steps in reverse order: If you followed the steps for disassembling the vacuum, simply reverse the process to put it back together.
  • Make sure all parts are securely attached: Before you put the vacuum back together, check that all parts are securely attached and seated properly. This will help prevent them from coming loose while you’re using the vacuum.
  • Use the right tools: If your vacuum requires screws, make sure you have a Phillips head screwdriver on hand. And if your vacuum has a belt, make sure you have a belt replacement tool (if needed). Using the right tools will make the process easier and will help prevent damage to the vacuum.
  • Take your time: Don’t rush the process of putting your Dirt Devil vacuum back together. Take your time and make sure each part is properly attached before moving on to the next step. This will help prevent mistakes and will ensure that your vacuum is working properly when you’re finished.

With these tips in mind, you should be able to put your Dirt Devil vacuum back together quickly and easily. And once it’s back together, you can enjoy the benefits of a clean and well-maintained vacuum cleaner.

How do you fix a dirt Devil vacuum that won’t turn on?

If your Dirt Devil vacuum cleaner won’t turn on, there could be a few different reasons for this. Here are some steps you can try to fix the problem:

  1. Check the power cord: Make sure the power cord is securely plugged into the vacuum and into the outlet. If the cord is loose or damaged, it may not be making a good connection, which could prevent the vacuum from turning on.
  2. Check the fuse or circuit breaker: If the outlet is working, but the vacuum still won’t turn on, the problem may be with the fuse or circuit breaker. Try replacing the fuse or flipping the circuit breaker to see if that fixes the problem.
  3. Check the switch: If the power cord and outlet are fine, the next step is to check the switch. Make sure the switch is in the “on” position and that it’s working properly. If the switch is damaged or stuck, it may not be able to turn the vacuum on.
  4. Check the motor: If the switch is working properly, the problem may be with the motor. The motor could be damaged or burned out, which would prevent the vacuum from turning on. In this case, you may need to replace the motor or take the vacuum to a repair shop for further diagnosis.

If you’ve tried these steps and your Dirt Devil vacuum still won’t turn on, it’s best to contact the manufacturer or a vacuum repair shop for further assistance. They will be able to diagnose the problem and recommend a solution.

Conclusion

In conclusion, taking apart a Dirt Devil vacuum cleaner is a simple process that can be done in just a few steps. By following the steps outlined in this guide, you can easily access and clean or repair the various parts of your vacuum, helping to keep it in good working condition.

And with some basic tools and a little bit of patience, you can easily put your vacuum back together and get it working like new again. Whether you’re looking to improve the performance of your vacuum or simply want to clean or repair it, taking it apart is an essential skill to have.

2 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *